Our customers in the USA are managed by JW Winco. Please, use the website of JW Winco: jwwinco.com
Our customers in the USA are managed by JW Winco. Please, use the website of JW Winco: jwwinco.com
The load rings GN 586.1 can be folded and rotated into all approved directions, carrying the full load in any tension direction.
They offer a high load carrying capacity and they are tested to meet safety standards (safety factor 4).
The rated load carrying capacity listed in the table is clearly marked on the attachment bolt. It applies to the most unfavourable load application of the load types listed opposite.
Load rings GN 586.1 comply with Mechanical Engineering Directive 2006 / 42 / EG and are BG tested.
The integrated RFID transponder clearly marks and identifies the sling and lifting gear, e.g. during the prescribed regular inspection.
The operating instruction contains further guidelines and is included with every load ring (see also at www.ganternorm.com/en/service).
Load ring
Steel
German Material No. 1.6541
Fixing holder
Screw
Steel, high-tensile tempered
Finish: Delta Tone
Bushing
Steel
Galvanic zinc plated
RoHS
| d1 | d2 | h1 | h2 | h3 | h4 | k1 | k2 | k3 | k4 | k5 | l1 | l2 | r | sw1 | sw2 | Tightening torque in Nm | Nominal Load in t (WLL) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| M 8 | 24 | 87 | 75 | 40 | 35 | 12 | 52 | 34 | 75 | 45 | 11 | 30 | 32 | 13 | 5 | 30 | 0.63 |
| M 10 | 24 | 87 | 75 | 39 | 36 | 12 | 52 | 34 | 75 | 45 | 15 | 30 | 32 | 17 | 6 | 60 | 0.9 |
| M 12 | 26 | 87 | 75 | 38 | 37 | 12 | 52 | 34 | 75 | 45 | 18 | 32 | 32 | 19 | 8 | 150 | 1.35 |
| M 16 | 30 | 99 | 85 | 39 | 46 | 13,5 | 56 | 38 | 86 | 47 | 22 | 34,5 | 38 | 24 | 10 | 150 | 2 |
| M 20 | 45 | 127 | 110 | 55 | 55 | 16,5 | 82 | 54 | 113 | 64 | 32 | 50 | 48 | 30 | 12 | 400 | 3.5 |
| M 24 | 45 | 143 | 125 | 67 | 58 | 18 | 82 | 54 | 130 | 78 | 37 | 50 | 48 | 36 | 14 | 760 | 4.5 |
| M 30 | 60 | 170 | 147 | 67 | 80 | 22,5 | 103 | 65 | 151 | 80 | 49 | 60 | 67 | 46 | 17 | 1000 | 6.7 |
|
Method of mounting |
|
|
|
|
|
|
|
|
|||
|
Number |
1 |
1 |
2 |
2 |
2 |
2 |
2 |
3 and 4 |
3 and 4 |
3 and 4 |
|
|
Angles of |
0° to 7° |
90° |
0° to 7° |
90° |
0° to 45° |
45° to 60° |
asymm. |
0° |
45° to 60° |
asymm. |
|
|
Factor |
1 |
1 |
2 |
2 |
1,4 |
1 |
1 |
2,1 |
1,5 |
1 |
|
|
M 8 |
0,63 t |
0,63 t |
1.26 t |
1.26 t |
0.88 t |
0.63 t |
0.63 t |
1.32 t |
0.95 t |
0.63 t |
|
|
M 10 |
0.90 t |
0.90 t |
1.80 t |
1.80 t |
1.30 t |
0.90 t |
0.90 t |
1.90 t |
1.35 t |
0.90 t |
|
|
M 12 |
1.35 t |
1.35 t |
2.70 t |
2.70 t |
1.90 t |
1.35 t |
1.35 t |
2.84 t |
2.00 t |
1.35 t |
|
|
M 16 |
2.00 t |
2.00 t |
4.00 t |
4.00 t |
2.80 t |
2.00 t |
2.00 t |
4.25 t |
3.00 t |
2.00 t |
|
|
M 20 |
3.50 t |
3.50 t |
7.00 t |
7.00 t |
4.90 t |
3.50 t |
3.50 t |
7.35 t |
5.25 t |
3.50 t |
|
|
M 24 |
4.50 t |
4.50 t |
9.00 t |
9.00 t |
6.30 t |
4.50 t |
4.50 t |
9.50 t |
6.75 t |
4.50 t |
|
|
M 30 |
6.70 t |
6.70 t |
13.40 t |
13.40 t |
9.50 t |
6.70 t |
6.70 t |
14.10 t |
10.00 t |
6.70 t |
|
|
The load capacity table shows the maximum loads in metric tons in relation to the mounting method at an operating temperature of -40 °C to +100 °C. The nominal load capacity refers to the most disadvantageous loading conditions, whereby a safety factor of 4 is taken into account for all values. The rotating load ring GN 586.1 may only be used if it is screwed on in accordance with the minimum screw-in length and set in the tension direction. The screw-on surface has to be plane and at a right angle to the threaded hole. When firmly mounted, the load ring must rotate freely by 360° and must not rest on edges or other lifting gear, e.g. on crane hooks. Rotating load rings are not suitable for permanent rotary movements under load. The operating instruction contains further guidelines and is included with every load ring (see also at www.ganternorm.com/en/service). |
|
||||||||||
Our service team is available from Monday to Friday between 7:00 AM and 5:30 PM: +49 7723 6507 - 0
