Indexing Plungers GN 717

Type: A - With pull ring, without locknut

List of Indexing Plunger Types Load Rating Information Stainless Steel Characteristics Metric ISO Thread DIN 13 Metric ISO fine thread DIN 13

Product description

Indexing plungers GN 717 are characterized by small dimensions. These indexing plungers are universally applicable due to their prevention of misalignments and positioning errors of the mating indexing bores.

Type A with pulling ring can be activated by finger in inaccessible places. If the indexing plungers are to be installed in areas which are not accessible by hand, type D with a pulling loop can be used for actuation from a distance. For example, this is possible with a retaining cable GN 111.2.

During assembly, the max. tightening torques shown in the table should not be exceeded when securing the lock nut.

Specification

Threaded body
SteelST
Zinc plated, blue passivated

Plunger pin
Stainless steel AISI 303

Pressure spring
Stainless steel AISI 301

Lifting ring / Wire loop
Stainless steel AISI 301

RoHS

Your contact

You are looking for a Ganter partner near you?

d₁ Plunger -0,05 Bore +0,03/+0,08	d₂	d₃	d₄	e	l₁	l₂	l₃	l₄	l₅ min.	l₆	l₇	A/F	max. tightening torque in Nm	Spring load in N≈ initial	end

3	M 6	14	6	6,9	33,5	3,5	12	4,5	10	32,9	12,9	6	2	3	12
3	M 6 x 0,75	14	6	6,9	33,5	3,5	12	4,5	10	32,9	12,9	6	3	3	12
4	M 6	14	6	6,9	33,5	4	12	4,5	10	33,4	12,9	6	2	3	12
4	M 8 x 1	14	6	9,2	40,4	4,5	16	6	13,5	42	15,5	8	8	5	24
5	M 8	18	7,2	9,2	45	5	16	6	13,5	42,5	15,5	8	7	5	24
5	M 8 x 1	18	7,2	9,2	45	5	16	6	13,5	42,5	15,5	8	7	5	24
5	M 10 x 1	18	7,2	11,5	45	5	16	6	13,5	42,5	15,5	10	22	5	24
6	M 10	24	9,5	11,5	57,1	6	20	7,5	17	54,4	20,9	10	15	5	21
6	M 12 x 1,5	24	9,5	13,8	57,1	6	20	7,5	16,5	54,4	20,9	12	38	5	21
8	M 12	30	11,8	13,8	71	8	24	9	20,5	66,9	25,9	12	20	6	22
8	M 12 x 1,5	30	11,8	13,8	71	8	24	9	20,5	66,9	25,9	12	20	6	22
8	M 16 x 1,5	30	11,8	19,6	71	8	24	9	20,5	66,9	25,9	17	80	6	22
10	M 16 x 1,5	30	11,8	19,6	74,8	10	26	9	22,5	70,9	25,9	17	80	4	27