JW Winco

Our customers in the USA are managed by JW Winco. Please, use the website of JW Winco: jwwinco.com

GN 20 Leveling Feet Stainless Steel, 3-A and DGUV Certified, without Mounting Holes, Hygienic Design

Photo

GN 20 Leveling Feet, Stainless Steel, without Mounting Holes, Hygienic Design
Stainless-Steel

Product Family Stainless Steel

Standard parts made of rustproof stainless steel have been designed for use in the food sector, in the chemical industry, for aggressive ambient conditions or for outdoor use.

  • corrosion-resistant
  • precise fit
  • environmentally friendly
Show all Stainless Steel products
Hygienic-Design

Product Family Hygienic Design

Standard Parts of the “Hygienic Design” product family are labeled with the HD icon. They combine high surface quality, freedom from dead spaces, non-scooped outer surfaces, and sealed bolting areas. A sealing concept based on FEM calculations ensures reliable contact pressure after installation.

  • suitable for use in hygienically sensitive areas
  • quick and easy cleaning
  • no dead spaces due to functional seals
  • certified according to EHEDG guidelines
Show all Hygienic Design products
FDA

FDA compliant

Product description

Information

Leveling feet GN 20 without mounting holes comply with the 3-A sanitary standard 88-01 and the DGUV Test guidelines, making them suitable for use in hygienic areas.

The bottom seal protects the area beneath the foot plate from dirt. For this, the foot must be pressed down by the weight of the machine. The sealing ring above the adjustment sleeve enables fastening without dead space. Due to the wiper or the joint sealing ring, the moving components are sealed against the environment.

The high quality finish prevents adherence of dirt and facilitates cleaning.

The values listed in the table for static load capacity refer to a purely vertical load in relation to the leveling foot. Under normal operating conditions bending loads or angular loads are not uncommon and result in a reduction of load capacity, which must be taken into consideration.

Specification

Spindle, adjustable sleeve, foot plate

  • Stainless steel AISI 304
  • Turned

Seals, blue, FDA compliant

  • Sealing ring
    NBR, hardness 70 ±5 Shore A
  • Wiper
    TPU, hardness 95 ±5 Shore A
  • Joint sealing ring
    H-NBR, hardness 85 ±5 Shore A
  • Bottom seal
    Silicone, hardness 85 ±5 Shore A

RoHS

Accessory

Cover Sleeves GN 20.1
Sealing Rings GN 7600
Wipers GN 7607

Technical drawing

3D
Hide technical drawing
GN 20 Leveling Feet, Stainless Steel, without Mounting Holes, Hygienic Design sketch

Article options / Table

Type

AWithout mounting holes
Show / Hide columns
d1d2l1d3l2l3A/F1A/F2Static load in kN
(see information)
60M 12175225251435171916
60M 16175225281935182230
80M 12175225251435171916
80M 16175225281935182230
80M 20185235322435242747
80M 24185235362935243067
100M 16175225281935182230
100M 20185235322435242747
100M 24185235362935243067
120M 16175225281935182230
120M 20185235322435242747
120M 24185235362935243067

Build & Price

Open 3D configurator
Specifications

Foot diameter d1
Thread d2
l1
Type

Design principles for Hygienic Design

3-A Sanitary Standard, Inc.

  • non profit and independent association in the USA
  • three interest groups:
    public and governmental health agencies, machine and food manufacturers
  • over 70 Sanitary Standards
  • examination of designs and processes, issue of certificates

3-A 88-01

Sealing concept

With the example of a GN 20 Hygienic Design levelling foot, the illustrated design shows how the various seal configurations can be designed.

Drawing Application example GN 20

Seals

For the standard parts which are listed in Hygienic Design, seals have the central function of protecting dead spaces, gaps and cracks from the penetration of cleaning fluids or product residues.
For this, a defined pre-tension or pressing of the seals and wipers is necessary for a reliable and permanent seal in the installed condition. Within the Hygienic Design product family, seal installation spaces and seal cross sections are calculated and designed with simulation software, so that the necessary surface compression is achieved on installation and the seal material is not subjected to excess pressure.
A fundamental differentiation can be made between static and moving seals:
Is the static seal, application examples shown below the top faces the mounting surface (sealing ring) and the bottom faces the contact surface (bottom seal), so that the corresponding pressure is achieved by tightening. It should be ensured that all surfaces which make contact with the seal have a surface finish of al least Ra 0.8 µm.
The moving seals on the adjustable sleeve (wiper) and the ball joint (joint sealing ring) of the foot are designed so that they allow adjustment in both height and angle. With these too, the installation space together with the cross section of the seal ensures a gap-free, pre-tensioned seal.
Depending on the version and the type of use, it may be the case that seals may need to be replaced in case of damage or for preventative maintenance. For this, Ganter supplies the relevant seals as spare parts or offers these under Sealing Rings GN 7600 as standard parts for spare parts.

Selected Part (How to order)

Total (net)
73,15
plus VAT 13,90 €
gross 87,05 €
In stock
Weight: 0,660 kg
If this article is new in our product range, it may happen that details concerning weight are as yet not listed.
If you do need weight details, please contact our Sales Department!
Phone +49 7723 6507 - 0
RoHS: Yes
This article is RoHS-compliant in application of Annex III., which means it complies with EU Directive 2011/65/EU, including extension (2015/863/EU), for restricting the use of certain hazardous substances in electrical and electronic devices. The Directive regulates the use of hazardous substances in devices and components. The implementation in national law is summarily described with RoHS(Restriction of (the use of certain) hazardous substances).
Please note our order discounts.
With a total value (net) per order:
from 175,00 € -> 10 % discount
from 275,00 € -> 20 % discount
from 375,00 € -> 30 % discount

Surcharge for small volume purchases:
-> 15,00 Euro
for value of goods less than 25,00 €
-> 10,00 Euro
for value of goods from 25,00 to 50,00 €
All prices in accordance with our price list No. 55, valid from 1 September 2022, plus VAT only valid for Germany.

CAD data

Other data formats

Quick-Login

For getting CAD data please enter you Email address. But we would be pleased, if you are fully registered.

Please enter the code you can find in the picture.

CAD Download Tutorial About CAD-Downloads
Save as favourite

Please enter the code you can find in the picture.

Do you find your product ?

Our service team is available from Monday to Friday between 7:00 AM and 5:30 PM: +49 7723 6507 - 0

To the customised elements | To the contact persons

GN 20-60-M12-175-AGN 20-60-M12-225-AGN 20-60-M16-175-AGN 20-60-M16-225-AGN 20-80-M12-175-AGN 20-80-M12-225-AGN 20-80-M16-175-AGN 20-80-M16-225-AGN 20-80-M20-185-AGN 20-80-M20-235-AGN 20-80-M24-185-AGN 20-80-M24-235-AGN 20-100-M16-175-AGN 20-100-M16-225-AGN 20-100-M20-185-AGN 20-100-M20-235-AGN 20-100-M24-185-AGN 20-100-M24-235-AGN 20-120-M16-175-AGN 20-120-M16-225-AGN 20-120-M20-185-AGN 20-120-M20-235-AGN 20-120-M24-185-AGN 20-120-M24-235-A

This could also be interesting...

Your contact

You are looking for a Ganter partner near you? Please select the country.

Ganter-Service

Our service team is available from Monday to Friday between 7:00 AM and 5:30 PM:

Request Callback
An error has occurred!
We have received your callback request and will contact you soon.